Local Reviews
for Elwood, IL
Our Reviews by City
Brennon E.
Furnace maintenance and safety inspection on two furnaces. Reset to factory specifications. Checked motors, relays, capacitors, contractors, circuit boards (upstairs unit faulty control board, replaced), pressure switches, bearings, fuses, wiring and connections, seals, fan, gas valve voltage and pressure, ignitor (faulty, replaced), flame sensor, thermostat, and heat exchanger. Cleaned out drain trap and all hoses and drain line. Replaced air filters. Both furnaces are working safely at this time. Customer is a VIP Service Plan member.
Brennon E.
Furnace repair. No heat call. Found furnace flame sensor extremely corroded and cracked. It was reading the flame intermittently. A furnace flame sensor is a safety device that detects if a furnace is producing a flame and burning gas. If the sensor doesn't detect a flame, it shuts down the furnace to prevent a gas leak. This helps prevent explosions and carbon monoxide poisoning. Replaced sensor and furnace system is back up and running.
Dan K.
Toilet replacement. Install customer supplied water closet. Also recommend customer switch toilet paper so breaks apart and not clog drain line.
Michael M.
ESTIMATE TO TROUBLESHOOT WALL MOUNTED DRINKING FOUNTAIN IN INFORMATION CENTER
Brennon E.
Heating repair ***No heat call*** After testing I found the inducer motor was making loud noise and working intermittently. Replaced inducer motor. A furnace inducer motor, also known as a draft inducer motor, is a critical component of a gas furnace that removes combustion gases from the heat exchanger and vents them outside. Replaced hot surface ignition due to working intermittently as well and tons of corrosion. Customer did agree to join out maintenance program. Went through the rest of the furnace testing pressure switches, gas valve voltage and pressure, flame sensor, blower motor amperage and capacitor. After replacing these parts , system is operating and heating as it should. Performed heat rise test. Everything is in adequate working condition. Furnace being older gave customer estimates for new furnace. ***Customer will have one more visit prepaid for 2025 cooling season.
Michael M.
ESTIMATE FOR NEW ENERGY EFFICIENT FURNACE WITH LIMITED LIFETIME WARRANTY.
Dan K.
Check sump pump, everything is working fine at this time. Went through system operation with customer so they are comfortable with their sump pump.
John M.
Rheem water heater service. Found the water heater gas valve was set to very hot, the highest temperature, upon arrival. Attempted to relight but was given code for high temperature shut down. Cooled down valve and it lit and functioned normally. Called Rheem to ask technical support and was told that the tank got too hot but the gas valve reset. I set the water heater temperature at setting "A" instead of the highest setting.
Pete W.
Cleaned intake screen for first floor Duravit urinal, flushing well at this time. Cleaned aerator for second floor lavatory sink.
Pete W.
Water filtering repair. Replace plastic piping for RO systems for first and third floor kitchen sinks.
Brennon E.
Cleaned and checked both condensers and both furnaces. Tested capacitor, contactor, fan motor amperage and compressor amperages. Replaced both capacitors with 45/5 mfd capacitors, and replaced both contactors using 2 poles. Fan amperages,compressor amperages and r 22 refrigerant levels were in accurate efficiency range and condition. On the furnaces tested inducer motor amperage, pressure switches,gas valve voltages, hsi, flame sensors and blower motor amperage and capacitors. Replaced both f.s due to corrosion. Everything else was in accurate working condition.
Michael M.
Commercial plumbing estimate to install soft seated check valve. Soft-seated valves manage water flow at water treatment plants. These valves prevent leaks and backflow, preserving treated water quality. Soft-seated valves are ideal for water contamination control tasks. This kind of valve helps protect human health and the environment.
John M.
Plumbing repair. Replaced shut off stops for dishwasher and refrigerator.
John M.
Replaced 8” center lavatory faucet, stops, and pop up.
Michael M.
ESTIMATE TO INSTALL 5 TON ENERFGY EFFICEINT ROOFTOP A/C SYSTEM.
Pete W.
Plumbing water leak. Found evidence of water leak from tub overflow, applied silicone between overflow piping and tub surface. Instructed customer to dry water in crawlspace and wait eight hours before using tub.
Dan K.
Work performed on 8/15/2024 401 E Mississippi Elwood Test and certified backflow’s 5- total 1-6” 1-3” 1-1 1/2” 2- 3/4” 26550 Industrial Port Rd. 3- total 1-4” 1-2” 1-1” 1-1” cleaning and retesting. 26453 S. Deer Run Dr. 1- 1 1/2”
John M.
Water leak. There appears to have been water on plastic sheeting in crawl space under the bathroom. Filled up tub, ran jacuzzi jets, drained tub, ran shower, and flushed toilet multiple times yet couldn’t find a leak. The subfloor and insulation are all completely dry so at this time there’s no reason to think anything from the bathroom is leaking. Recommend keeping an eye on it and if water appears we’ll look at what fixtures were used and if it was raining.
John M.
Installed new Kohler toilet and tested for safe operation. Removed old toilet and cleaned work area.
Dan K.
Test and certified 3 backflow’s file paperwork with city per state code 1-2” double check backflow 1-3/4” double check backflow 1-3/4” RPZ backflow
John M.
I recently completed a job repairing 6 gas leaks in a garage and crawl space. I found the leaks using specialized tools and fixed them using professional techniques to ensure a safe and long-lasting repair.
John M.
Pump service call. I sealed the ejector pump lid.
Chris S.
Inspected rooftop HVAC unit, main breaker inside building was tripped, reset and tested unit. Pulling 60 amps and breaker is 90 amp. Breaker is warm to the touch. Talked to Larry about calling electrical company to check out panel. 480 volt, 3 Phase.
Brennon E.
Air conditioner repair. No AC call. Found contactor was working intermittently and fluttering on and off. Replaced contactor and unit is working and cooling as it should.
Dan K.
COMMERCIAL HVAC MAINTENANCE. ESTIMATE TO CLEAN, TEST & RESET 2 NEW AIR CONDITIONERS TO FACTORY SPECIFICATIONS.
