Read below what your Minooka, IL neighbors say about our plumbers and HVAC team. You'll like what you see!
Local Reviews
for Minooka, IL
Our Reviews by City
Brennon E.
Furnace maintenance and safety inspection. Reset two furnaces to factory specifications. Checked motors, relays, capacitors, contractors, circuit boards, pressure switches, bearings, fuses, wiring and connections, seals, fan, gas valve voltage and pressure, ignitor, flame sensor, thermostat, and heat exchanger. Cleaned out drain trap and all hoses and drain line. Replaced air filter. Replaced humidifier pad using a (35). Cycled both furnaces a few times. Furnaces are working safely at this time. Customer is a VIP Service Plan member.
Brennon E.
Cleaned and serviced furnace furnaces. Tested. All working and heating as they should be at this time. Replaced AprilAir 110 & 410 filters. In furnace that takes AprilAir 410, (main furnace), found a little water in cabinet. Removed inducer motor and retighten collector box screws and resealed inducer motor. All thermostats are operating as they should at this time. Customer might replace three thermostats in spring. (Bring with/make note for spring visit along with filters. Replaced two humidifier pads, (35). Everything is in accurate working condition. Customer will renew maintenance programs in spring. Last visits being used today.
Chris S.
Commercial ventilation repair. Removed exhaust fan, need to order replacement parts. Complete rebuild of exhaust fan, motor and blower wheel. Part had to be factory ordered.
Dan K.
Furnace repair. Tested system and found a faulty ignition system. Install the flame rod, filter, control board. A safety device called a flame rod, sometimes known as a flame sensor, checks to see if a furnace is emitting flames and burning gas. The furnace control board is an essential aspect of maintaining the efficiency and safety of your home's heating system. Cycle furnace twice, system is running, burners fired right away. Working as of now.
Brennon E.
Cleaned and serviced furnace. Tested inducer motor, pressure switches, hsi, gas valve voltage and pressure, flame sensor, and blower motor amperage. Replaced furnace filter that customer provided. Replaced ignitor and gas flame sensor due to corrosion. Everything else was in accurate working condition. System is operating and heating as it should at this time. Customer will renew plan in the spring.
Chris S.
Commercial HVAC service call. Troubleshoot 2 north units, repair and replace belts.
Brennon E.
Furnace maintenance. Cleaned and serviced furnace. Tested inducer motor, pressure switches, flame sensor, ignitor, gas valve voltage, blower motor amperage and capacitor. Checked thermostat and heat exchanger. Blew out drain line. Replaced furnace filter that customer provided. Everything is in accurate working condition. Customer renewed VIP maintenance program. Will have 2025 season of cleaned and checks prepaid.
Brennon E.
Goodman furnace maintenance. Cleaned and serviced furnace. Furnace is a 80%, 80,000 btu Goodman. Tested inducer motor, pressure switches, ignition, gas valve voltage, flame sensor, blower motor amperage and capacitor. Inspected heat exchanger and thermostat. Everything is in accurate working condition. Furnace is operating and heating as it should at this time. Customer signed up for VIP maintenance program. One visit is being used today and they will have one more visit remaining for 2025 cooling season. Giving customer estimate for new water heater due to age (2012).
Chris S.
Boiler maintenance. Service boiler for season. Cleaned, tested and reset to factory specifications. Boiler is operating safely and efficiently today.
Dan K.
American Standard high efficiency furnace repair. After cleaning my inspection found screens on pvc pipe outside, the intake and exhaust blocked. The furnace was locked out on the pressure switch so I went back in to reset furnace. The furnace came on found 3 problems 1- draft inducer really noisy 2- blower motor really noisy 3- dirty filter Replaced inducer motor and blower. Furnace is a lot quieter. I also washed blower wheel when changing the motor.
Pete W.
Sewer, drain service. Checked usual sources of sewer odor. Added water to floor drain in rear restroom. Found clean out, cover in hallway loose and had a hole in it, replaced and properly sealed cleanout cover in hall. If problem persists will have to perform a smoke test to determine source of odor.
Pete W.
Turned off air conditioning, turned up temperature for radiant heat. Instructed homeowner and caretaker as to operation. Shut water off to out-building to prevent freezing in the winter.
Dan K.
Carrier Furnace maintenance. Cleaned and serviced furnace. Tested flame sensor, pressure switches, ignitor, gas valve voltage, blower motor amperage and capacitor. Everything tested is accurate working condition. Replaced furnace filter. Install an efficient Bradford White 40 gallon water heater to local code. Remove old water heater tank. Test for safe operation. Clean up work area.
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switches, hsi, gas valve voltage, blower motor amperage and capacitor. Cleaned out exhaust pipe and drain. Replaced furnace filter that customer provided. The blower motor capacitor was extremely low and replaced using a 10 mfd. Everything else is in adequate working condition.
Brennon E.
Rooftop HVAC unit maintenance. Cleaned and serviced RTU unit. Replaced filters. Checked refrigerant levels and cleaned out condenser coil due to being extremely covered in cottonwood. Then went through the heating side. Cleaned igniter and burners where gas comes out. Tested blower motor amperage and capacitor. Everything is in accurate working condition.
Chris S.
Estimate for new energy efficient HVAC system with strong warranty.
Pete W.
Cleaned Venturi and checked water softener, appears to be working properly at this time.
John M.
Pulled man hole cover to access storm drain lines. There’s a 10” and 24” line coming in and it’s 36” on the discharge side. These pipes are too big for out camera, Dave will talk to someone that has the necessary equipment and schedule a time to investigate.
Pete W.
Drain cleaning. Cleared kitchen sink drain with flex shaft machine, flowing well at this time. Pitch and drain line is less than it should be, would need to rehang the whole line to correct.
John M.
Faucet was leaking down into the cabinet. In order to match the white sink the customer would like another white faucet which has to be ordered, it should be in within the next few days. Returned on 8/5/24 and replaced faucet. Customer has $50 coupon.
Pete W.
Commercial washroom plumbing repair. Rebuilt lavatory faucet in truckers washroom.
Chris S.
Repaired A/C unit, we replaced compressor under parts warranty.
Brennon E.
Air conditioner tune-up. I cleaned, washed out, and serviced condensing units. Tested capacitor, contactor, fan motor amperage and compressor amperage. Everything was in adequate working condition. Checked r410a refrigerants. They too were in accurate efficiency range. Replaced furnace filters. (1) 16x25x1, and (1) 16x20x1 that customer provided. Customer need (1) AprilAir filter that I provided. First annual service plan visit and will have one more fall visit for furnaces.
Brennon E.
Air conditioner annual maintenance. I cleaned, washed out, and serviced condensing unit. Tested capacitor, contactor, fan motor amperage and compressor amperage. Everything was in adequate working condition. Checked R22 refrigerant levels. They too were in accurate efficiency range. Customer just replaced furnace filter the 3rd of July. System is cooling efficiently as it should at this time. David would like quote for new water line and main shut off.
Pete W.
Toilet repair. Faulty fill and flush valve. Replaced and tested toilet for proper operation.
